mirror of
https://github.com/AllStarLink/ASL3-Docker.git
synced 2026-08-26 14:27:28 -04:00
145 lines
8.1 KiB
Text
145 lines
8.1 KiB
Text
;***************************************************
|
|
;******** Template-tized simpleusb.conf ********
|
|
;***************************************************
|
|
; Note to editors: set tabs to 4 space characters. No wrap to keep comments neat.
|
|
; vim: tabstop=4
|
|
;
|
|
; SimpleUSB channel driver Configuration File
|
|
;
|
|
;;;;; New to ASL3 ;;;;;
|
|
;;;;; The SimpleUSB "tune" settings have moved to ;;;;;
|
|
;;;;; this file. The simpleusb_tune_usb_1999.conf ;;;;;
|
|
;;;;; file is no longer used. ;;;;;
|
|
|
|
; If you are going to use this channel driver, you MUST enable it in modules.conf
|
|
; change:
|
|
; noload => chan_simpleusb.so ; CM1xx USB Cards with Radio Interface Channel Driver (No DSP)
|
|
; noload => res_usbradio.so ; Required for both simpleusb and usbradio
|
|
; to:
|
|
; load => chan_simpleusb.so ; CM1xx USB Cards with Radio Interface Channel Driver (No DSP)
|
|
; load => res_usbradio.so ; Required for both simpleusb and usbradio
|
|
|
|
[general]
|
|
;------------------------------ JITTER BUFFER CONFIGURATION --------------------------
|
|
; jbenable = yes ; Enables the use of a jitterbuffer on the receiving side of an
|
|
; simpleusb channel. Defaults to "no". An enabled jitterbuffer will
|
|
; be used only if the sending side can create and the receiving
|
|
; side can not accept jitter. The simpleusb channel can't accept jitter,
|
|
; thus an enabled jitterbuffer on the receive simpleusb side will always
|
|
; be used if the sending side can create jitter.
|
|
|
|
; jbmaxsize = 200 ; Max length of the jitterbuffer in milliseconds.
|
|
|
|
; jbresyncthreshold = 1000 ; Jump in the frame timestamps over which the jitterbuffer is
|
|
; resynchronized. Useful to improve the quality of the voice, with
|
|
; big jumps in/broken timestamps, usually sent from exotic devices
|
|
; and programs. Defaults to 1000.
|
|
|
|
; jbimpl = fixed ; Jitterbuffer implementation, used on the receiving side of an simpleusb
|
|
; channel. Two implementations are currently available - "fixed"
|
|
; (with size always equals to jbmax-size) and "adaptive" (with
|
|
; variable size, actually the new jb of IAX2). Defaults to fixed.
|
|
|
|
; jblog = no ; Enables jitterbuffer frame logging. Defaults to "no".
|
|
;-----------------------------------------------------------------------------------
|
|
|
|
[node-main](!)
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;;;;; Template for all your SimpleUSB nodes ;;;;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
eeprom = 0 ; EEPROM installed: 0,1
|
|
; 0 = no (default)
|
|
; 1 = yes
|
|
|
|
hdwtype = 0 ; Leave this set to 0 for USB sound fobs designed for app_rpt
|
|
; or modified cmxxx sound fobs.
|
|
; 1 is for Dingotel/Sph interfaces.
|
|
; 2 is for NHC interfaces.
|
|
; 3 is for a custom interface.
|
|
|
|
; Receiver parameters
|
|
rxboost = no ; no = 20db attenuator inserted, yes = 20db attenuator removed
|
|
; Set to yes for additional gain if using a low-level receiver output
|
|
; CM119B devices are hard coded to rxboost 20dB attenuator removed
|
|
|
|
carrierfrom = usbinvert ; no,usb,usbinvert
|
|
; no - no carrier detection at all
|
|
; usb - from the COR line on the USB sound fob (Active high)
|
|
; usbinvert - from the inverted COR line on the USB sound fob (Active low)
|
|
; pp - from parallel port (Active high)
|
|
; ppinvert - from the inverted parallel port (Active low)
|
|
|
|
ctcssfrom = usbinvert ; no,usb,usbinvert
|
|
; no - CTCSS decoding, system will be carrier squelch
|
|
; usb - CTCSS decoding using input from USB sound fob (Active high)
|
|
; usbinvert - from the inverted CTCSS line on the USB sound fob (Active low)
|
|
; pp - from parallel port (Active high)
|
|
; ppinvert - from the inverted parallel port (Active low)
|
|
|
|
deemphasis = no ; enable de-emphasis (input from discriminator)
|
|
|
|
plfilter = yes ; enable PL filter
|
|
|
|
rxondelay = 0 ; Number of 20mSec intervals following the release of PTT.
|
|
; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging"
|
|
; or "Relay Racing". A positive value here will instruct the usbradio
|
|
; driver to ignore the COR line for a specified number of 20mSec
|
|
; intervals following the release of PTT. Use this ONLY on simplex
|
|
; nodes, and leave commented out for repeaters or other full duplex nodes.
|
|
|
|
txoffdelay = 0 ; Ignore the receiver for a specified number of 20 millisecond
|
|
; intervals after the transmitter unkeys.
|
|
; This is useful when setting up a half-duplex link with an existing
|
|
; repeater, where you need to ignore the repeater's hangtime.
|
|
|
|
; Transmitter parameters
|
|
txmixa = voice ; Left channel output (A): no,voice
|
|
; no - Do not output anything
|
|
; voice - output voice only
|
|
|
|
txmixb = no ; Right channel output (B): no,voice
|
|
; no - Do not output anything
|
|
; voice - output voice only
|
|
|
|
invertptt = no ; Invert PTT: no,yes
|
|
; no - ground to transmit
|
|
; yes - open to transmit
|
|
|
|
preemphasis = no ; Perform standard 6db/octave pre-emphasis
|
|
|
|
; pager = no ; no,a,b (e.g. pager = b means "put the normal repeat audio on channel A, and the pager audio on channel B")
|
|
|
|
; duplex3 = 0 ; duplex 3 gain setting (0 to disable)
|
|
|
|
clipledgpio = 1 ; Enable ADC Clip Detect feature to use a GPIO output (0 to disable).
|
|
; Supports URI Clip LED by setting a GPIO (if available) high for 500mS
|
|
; when clipping detected. Value = GPIO# to use (GPIO1 recommended)
|
|
|
|
legacyaudioscaling = no ; If yes, continue to do raw audio sample scaling and clipping, resulting in Tx audio levels increasing
|
|
; by 0.78dB and Rx audio levels increasing by 0-1.5dB. Should be set to no unless you have an existing
|
|
; node with precisely adjusted audio levels and are unable to adjust them. This parameter and associated
|
|
; scaling/clipping code will be deleted once existing installs have been able to verify their audio levels
|
|
|
|
;;; End of node-main template
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;;;;;;;;;;;;;;;; Configure your nodes here ;;;;;;;;;;;;;;;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;
|
|
; Note: there is no need to duplicate entire settings. Only
|
|
; place settings that are different than the template.
|
|
;
|
|
; Note: the device string is automatically found when the
|
|
; USB setting "devstr=" is empty.
|
|
;
|
|
; Note: the interface "tune" settings will be added to the
|
|
; per-node settings (below).
|
|
|
|
[1999](node-main)
|
|
|
|
;;;;; ASL3 Tune settings ;;;;;
|
|
devstr=
|
|
rxmixerset=500
|
|
txmixaset=500
|
|
txmixbset=500
|